Your watercooling and modding distributor Your watercooling and modding distributor

Alphacool flow indicator G1/4 with rpm signal - Plexi

  • 71221
  • 17176
  • 4250197171762
  • 0,055 kg

> 250 available in stock

21,79 € *

Ceny inkl. zákonná DPH plus náklady na zásilku

The Alphacool flow sensor is designed to fit the needs of computer water cooling enthusiasts. As...more
Product Information

The Alphacool flow sensor is designed to fit the needs of computer water cooling enthusiasts. As other flow sensors have unusual threads or need an additional electronic device, this Alphacool flow sensor can be used with G1/4 fittings and can be directly connected with a standard 3-pin fan cable to a mother board, a fan controller or an electronic device (Heatmaster, Aquaero, T-Balancer)

Connect to a main board:
The flow sensors will be detected from the main board like a normal 3-pin fan. Normally it is possible to set the main board software this way, that depending on the rotation speed (or if there is no rotation at all) the computer will be shut down. This makes it possible to have a very good and save way to protect the hardware without additional costs.

Connect to a fan controller:
The flow sensor will be detected and will get the input of the rotation speed like a normal 3-pin fan. If the fan controller includes a Display and / or an alarm function, they can be used also with the flow sensor.

Connect to an electronic device:
The signal from the flow sensor will be detected as a “puls” and can be calculated to the needed unit of measurement (for example l/h or g/h). If you use an Alphacool Heatmaster, it is possible to start an alarm when the flow rate is too low or even to shut down the computer.

Technical data:
Material: Plastic
Threads: G1/4
Measurements: Length: 46mm, outside diameter: 52mm
Cable length: 33cm
Cable plug: 3-pin

Folgende Werte sind ermittelt worden Toleranz +/- 10%:
125rpm entsprechen 190 Liter / Pro stunde
150rpm entsprechen 250 Liter / Pro stunde
175rpm entsprechen 320 Liter / Pro stunde
200rpm entsprechen 390 Liter / Pro stunde
225rpm entsprechen 450 Liter / Pro stunde
250rpm entsprechen 500 Liter / Pro stunde

In praxis the actual pulse per 1000ml may verify, depending on the type of construction and the system you use. Therefore we recommend to make a precise measurement of the flow rate in an installed system whenever exact flow rates are needed (for example for industrial purposes)

Awards
Questions & Answers more
Questions & Answers
2 Frage(n) in anderen Sprachen.
Klicken Sie hier, um diese Frage(n) anzuzeigen.
Question from Guest #241563 from 05. May 2016
This flow meter has a minimum speed below which no marks or otherwise should mark?
Antwort von Aquatuning GmbH vom 05. May 2016
It is not descriped, so i think you can use it without any problems.
Question from Brigitte K. from 12. December 2017
Mein Mainboard zeigt 470rpm an. Kann das sein? Laut den Werten hier im Artikel hätte ich einen Durchfluß von 900L/h. Habe eine VPP655 (Stufe 5) + 3Monster Radiatoren (480,360,240). Habe ich da einen Denk-Fehler?
Antwort von Aquatuning GmbH vom 12. December 2017
Die Tabelle in der Beschreibung scheint nicht korrekt zu sein. Es scheint das Komma falsch gesetzt zu sein. Sie dürften ca. 90L/h Stunde haben. 900L/h sind mit keiner Pumpe in einem Kreialauf möglich.
Do you have a question?
Všimnite si: Vaša otázka bude verejne viditeľná a odpovedá na ňu člen našej komunity, ako aj náš tím podpory. Môžete upraviť svoje používateľské meno a nastavenia e-mailových upozornení vo svojom účte zákazníka.
Read, write and discuss reviews...more
Reviews
5 hviezdy:
(4)
4 hviezdy:
(3)
3 hviezdy:
(1)
2 hviezdy:
(1)
1 hviezdy:
(0)
9 Hodnotenie v iných jazykoch.
Kliknutím sem zobrazíte tieto hodnotenia.
Napíšte recenziu
Oznámenia: Vaša recenzia bude zverejnená po ručnom vyčiarknutí.
-33%